All four programmers are built for in-system programming in volume production. They differ in channel count, where they sit on the line, which memories they can program and how they connect to the ATE. This guide sets out the differences in one table, then matches them to common production situations.
gree-tech supplies four in-system programmers: FlashRunner 2.0, FlashRunner 2.0 HS and FlashRunner 2.0 NXG from SMH Technologies, and WriteNow! from Algocraft. All four run standalone or under host control. The figures below come from the user manuals and product pages.
Comparison
| FlashRunner 2.0 | FlashRunner 2.0 HS | FlashRunner 2.0 NXG | WriteNow! | |
|---|---|---|---|---|
| Programming channels | 4, 8, 12 or 16, upgradeable by software licence | Up to 32 (up to 8 active modules of 1, 2 or 4 channels each) | 1 to 4, upgradeable by software licence | 1, 2, 4 or 8 sites |
| Expansion | The 16-channel model reaches 32 channels with a demultiplexer module (programmed in two passes) | Active modules can be mixed to suit the device type | — | Up to 4 demultiplexer boards stacked on each ISP connector; up to 32 channels on WN-PRG08A |
| Where it sits | In the fixture, 2 × 48-pin DIN connectors | Control unit in the cabinet; active modules close to the devices on USB-C cables of up to 6 m | In the fixture; body 17.6 mm thick | In the fixture, DIN41612 connector |
| Host interfaces | Gigabit LAN, USB-UART, both isolated | Gigabit LAN, USB-UART, both isolated | Gigabit LAN, USB, both isolated | USB, LAN (100 Mbit/s, isolated), RS-232 (isolated) |
| Standalone / ATE control | Isolated control interface: selects up to 32 projects, start, BUSY, PASS/FAIL per channel | Isolated parallel control interface | Isolated control interface | Isolated low-level interface: project select, start, BUSY, OK/ERR per site |
| Device types | Microcontrollers, serial memories and more | Microcontrollers, serial memories, plus dedicated modules for eMMC, UFS, OCTO-SPI and parallel NAND; USB, Automotive Ethernet and CAN/CAN-FD modules | Microcontrollers, serial memories, eMMC, parallel NAND | Microcontrollers, serial memories; parallel memories on WN-PRG08A only |
| Relay isolation | Optional relay barrier | Active modules optionally with built-in relay barrier | Optional relay barrier | Built into WN-PRG01A, optional module for the other models |
| Functional safety certification | Not stated in the product documentation | Not stated in the product documentation | Not stated in the product documentation | Certified by a third-party lab as compliant with ISO 26262 and IEC 61508 |
Device coverage
As of November 2026 the device list has 32,609 parts. Of these, 31,171 are listed for FlashRunner 2.0, 2.0 HS and 2.0 NXG alike; 873 for 2.0 HS and 2.0 NXG only, mostly parallel NAND, eMMC and OCTO-SPI memories; 57 for FlashRunner 2.0 only, mostly parallel NOR flash. WriteNow! lists 11,272, of which 498 are supported by WriteNow! alone. Before choosing, check each part in the device list.
The automotive MCU families covered earlier in this series:
| Family | Entries | FlashRunner 2.0 / HS / NXG | WriteNow! |
|---|---|---|---|
| AURIX™ TC3xx | 76 | 76 | 65 |
| S32K1 / S32K3 (microcontrollers only) | 33 | 33 | 30 |
| RH850 | 239 | 237 | 204 |
| SPC5 and Stellar | 90 | 90 | 44 |
| TRAVEO™ T2G | 385 | 385 | 53 |
Matching the programmer to the line
Single boards or small panels at an ICT or functional test station, with a moderate cycle time. FlashRunner 2.0 NXG: 1 to 4 channels in a small body. Start with one channel and upgrade by software licence as volumes grow.
Multi-board panels programmed in one go in the fixture. FlashRunner 2.0: 4 to 16 independent channels, and up to 32 with a demultiplexer module on the 16-channel model. Because the channels run independently, one panel can carry different parts.
Large memories, or many channels with long wiring. FlashRunner 2.0 HS: the active modules sit right next to the devices, which keeps long cables from degrading the signals. Dedicated modules handle eMMC, UFS, OCTO-SPI and parallel NAND, and end-of-line stations can program over USB or Automotive Ethernet.
Projects that require a programming tool with functional safety certification, or lines already running Algocraft equipment. WriteNow!: 1 to 8 sites, expandable to 32 channels, with legacy interfaces such as RS-232.
These are starting points; the final choice also depends on the parts, the cycle time and the space in the fixture. gree-tech can run a demo on your sample boards to confirm it.
Questions and answers
Can FlashRunner and WriteNow! be used on the same line? Yes. Both connect to the ATE over LAN or a control interface, and their project files are independent.
Do the three FlashRunner models share their software? All three use FlashRunner Workbench, the same DLL and ASCII commands, and share one FlashRunner 2.0 Programmer’s Manual. Before switching models, check the status of your parts on the new model.
Can the channel count be increased later? FlashRunner 2.0 (4→8, 12→16), 2.0 NXG (1→4) and the 2.0 HS control unit (4→8 module ports) are all upgraded by software licence. On WriteNow! the number of sites depends on the model, and demultiplexer boards add channels.