TC3xx is the AURIX™ generation most automotive lines program today. This guide covers its programming interfaces, the memory regions to program, the steps that tend to go wrong in production, and how many parts each of the four programmers supports.
AURIX™ TC3xx is Infineon’s family of 32-bit multicore automotive microcontrollers built on the TriCore™ architecture. According to Infineon, the range spans one to six TriCore™ cores and up to 16 MB of flash, supports ISO 26262 ASIL-D and integrates a hardware security module (HSM). Typical applications are engine and transmission control, traction inverters, DC/DC converters, battery management, on-board chargers, braking and steering, ADAS and radar, and gateways. For the newer generation, see Programming Infineon AURIX™ TC4xx devices with FlashRunner.
Which TC3xx parts the device list covers
As of November 2026 the device list has 76 TC3xx parts in eight families: TC32x (10), TC33x (16), TC35x (4), TC36x (13), TC37x (8), TC38x (5), TC39x (17) and TC3Ex (3).
| Programmer | Parts supported | Protocols |
|---|---|---|
| FlashRunner 2.0 / 2.0 HS / 2.0 NXG | 76 (70 available now, 6 with the algorithm delivered within 20 days of order) | DAP, JTAG |
| WriteNow! | 65 | DAP, JTAG |
The device list is the reference for the status of each part; you can also search for TC3.
Memory regions to program
FlashRunner’s device data lists three regions for TC3xx:
- FLASH (PFlash, program flash): from 1 MB on TC32x to 16 MB on TC39x.
- DATA (DFlash, data flash): from 128 KB to about 1.13 MB, depending on the part.
- UCB (user configuration blocks): 24 KB.
The UCBs need the most care on the line. Infineon documents that they sit in DFLASH0 and include the boot mode headers (BMHD), of which at least one valid original/copy pair must be programmed for the device to start from flash as configured; the debug interface configuration (UCB_DBG) is held there too. Infineon’s own AURIX Flasher tool leaves UCB programming off by default, because a wrong UCB configuration can leave the device unusable. Our advice: validate the UCB image on samples first, make UCB programming the last step of the script, and keep ORIG and COPY consistent. A UCB setting can also give the HSM exclusive access to DFLASH1, so if the project uses the HSM, decide early which step writes the HSM data, and with what.
Whether parts whose debug interface is already password-protected can be reworked on the line depends on the part and its configuration; check with gree-tech before you rely on it.
Line integration
- Parallel channels: FlashRunner 2.0 has 4 to 16 independent channels (the 16-channel model extends to 32 with a demultiplexer module); 2.0 HS drives up to 8 active modules from one control unit and programs up to 32 devices at once; 2.0 NXG has 1 to 4 channels; WriteNow! has 1, 2, 4 or 8 programming sites.
- ATE and ICT: FlashRunner’s control interface selects one of up to 32 stored projects, starts it and reports PASS/FAIL per channel; the unit can also be driven over LAN, USB or the DLL (C/C++, C#, LabVIEW, TestStand). On ICT, a relay barrier disconnects the programming lines from the board while it is being tested.
- Shorter cycle time: SMH’s application note AN00183 describes several techniques, such as verifying by checksum instead of a full readout where the device supports it, skipping blank pages (IGNORE_BLANK_PAGE), and running a blank check before deciding to erase.
Questions and answers
Should I use DAP or JTAG? Both protocols are listed for these parts. DAP is the debug and access interface Infineon designed for AURIX™; before designing the fixture, check in the device manual which interface your board brings out.
Do the UCBs have to be programmed on the line? Not necessarily. If they are configured upstream or by a supplier, the line can program PFlash and DFlash only. If you do program them, validate the complete image on samples first.
What does “20 days” mean in the device list? The algorithm for that part is delivered within 20 days of order. It does not mean the part is unsupported.
Can one FlashRunner program different TC3xx parts at the same time? FlashRunner’s channels are independent of each other. If a panel mixes different parts, send us the board configuration so we can confirm the project set-up.