RH850 is used widely in body, chassis and instrument-cluster electronics and in the new domain and zone controllers. This guide explains how RH850 enters serial programming mode on the line, which regions to program, what to watch with ID authentication and option bytes, and how many parts each programmer supports.
RH850 is Renesas’s family of 32-bit automotive microcontrollers, qualified to AEC-Q100 and supporting ISO 26262 functional safety. Renesas positions the F1x series for body electronics such as body control modules, gateways, HVAC and lighting; P1x for chassis control; D1x for instrument clusters; and the 28 nm U2x series (U2A, U2B, U2C) for vehicle motion, battery management, safety systems and zonal architectures.
RH850 in the device list
As of November 2026 the RH850 family has 239 parts (R7F701xxx and R7F702xxx).
| Programmer | Parts supported | Protocols (from the data) |
|---|---|---|
| FlashRunner 2.0 / 2.0 HS / 2.0 NXG | 237 (198 available now, 39 with the algorithm delivered within 20 days of order) | CSI |
| WriteNow! | 204 | UART (UART-CH0), clock-synchronous serial (SIO-CH0); CSI and UART on some parts |
FlashRunner and WriteNow! name the protocols differently (CSI and SIO are both clock-synchronous serial), so wire the fixture according to the programmer you choose and the device manual.
Entering programming mode
SMH’s application note AN00175 lists the signals needed to program RH850 in-system over CSI: the mode-select pins FLMD0 and FLMD1, serial data out FPDT, data in FPDR and clock FPCK (JP0_1, JP0_0 and JP0_2 on its example device), plus RESET, VDD and GND. The programmer drives FLMD0 around power-up and reset to put the device into serial programming mode, so the board’s FLMD0 pull resistor and reset circuit must let the programmer take control.
The project must set the communication mode, the external oscillator frequency (FOSC), the communication clock (SCLK), the security code and the protection mode. FOSC must match the crystal actually fitted on the board. In AN00175’s example script the device allows at most 24 MHz for FOSC and 5 MHz for SCLK; check the documentation for other parts.
Memory regions to program
FlashRunner’s data lists these regions for RH850: FLASH (code flash, up to 16 MB), EEPROM (data flash), the extended user area (EXT_USER_AREA), the ID code (ID_CODE) and the option bytes (OPTION_BYTES). Newer parts such as R7F702xxx add a user boot area, a configuration area and a security area.
From AN00175:
- Option bytes: always written as 32 bytes, little-endian, ordered OPBT0 to OPBT7. A wrong value can change how the device starts and is configured, so export them from the Renesas tool and check them.
- ID authentication: the protection mode is either ID authentication or command protection, with a 16-byte security code. Once an ID is set, later connections need the same ID, so make ID handling part of the line’s data management.
- ICU-S: enabling the ICU-S (Intelligent Cryptographic Unit) cannot be undone; run it only once the decision is confirmed.
- After programming, the device can compute a checksum itself for comparison with the expected value.
Line integration
FlashRunner 2.0 (4 to 16 channels, extendable to 32), 2.0 HS (up to 32 channels), 2.0 NXG (1 to 4 channels) and WriteNow! (1 to 8 sites) all connect to ATE or ICT through a control interface or LAN and report a result per channel. Every FlashRunner channel has programmable voltage outputs that can power the target board; where the programmer shares test probes with ICT, add a relay barrier.
Questions and answers
CSI or UART for RH850? Both are serial programming methods defined by Renesas. FlashRunner’s data lists CSI and WriteNow!’s mostly UART or SIO, so match the choice to the pins your board brings out.
What if a returned board will not connect? One possible reason is that ID authentication or protection is set on the device. Find the original ID first, then proceed as the device manual allows.
Can the option bytes differ from board to board? They can be loaded as dynamic data and written per board, but in most projects every board is the same and keeping them in the image is simpler.